Outdoor LED Power Supply 100W

100W Outdoor LED Power Supply
  • 100W Outdoor LED Power Supply
  • 100W Outdoor LED Power Supply
  • 100W Outdoor LED Power Supply

Features:
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
The outdoor power supply is up to 93% efficient
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67 design for outdoor lighting supply
Class 2 power unit
Three-in-one dimming function (1 〜10Vdc or PWM signal or resistance)
Suitable for LED lighting and street lighting applications
Compliance to worldwide safety regulations for LED lighting supply
Suitable for dry / damp / wet locations

Technical Specification:

MODEL PW100-24D-040A-MW
OUTPUT DC VOLTAGE 24V
CONSTANT CURRENT REGION Note.4 12-24V
RATED CURRENT 4A
RATED POWER 96W
RIPPLE & NOISE (max.) Note.2 150mVp-p
VOLTAGE ADJ. RANGE Note.6 22 -27V
CURRENT ADJ. RANGE Can be adjusted by internal potentiometer
2.5 ~4A
VOLTAGE TOLERANCE Note.3 ±1.0%
LINE REGULATION ±0.5%
LOAD REGULATION ±0.5%
SETUP, RISE TIME Note.8 1200ms,50ms/115VAC 500ms,50ms/230VAC at full load
HOLD UP TIME (Typ .) 16ms at full load 230VAC /115VAC
INPUT VOLTAGE RANGE Note.5 90 -305VAC 127-431VDC
FREQUENCY RANGE 47~63Hz
POWER FACTOR (Typ .) PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
TOTAL HARMONIC DISTORTION THD< 20% when output loading ≥ 60% at 115VAC/230VAC input and output loading ≥ 75% at 277VAC input
EFFICIENCY (Typ .) 93%
AC CURRENT (Typ . ) 1.2A /115VAC 0.55A/230VAC 0.5A/277VAC
INRUSH CURRENT (Typ . ) COLD START 60A(twidth =415m s measured at 50% Ipeak ) at 230VAC
LEAKAGE CURRENT <0.75mA/277VAC
PROTECTION OVER CURRENT 95-106%
Protection type: Constant current limiting, recovers automatically after the cause of the fault is removed
SHORT CIRCUIT Constant current limiting, recovers automatically after the cause of the fault is removed
OVERVOLTAGE 28-34V
Protection type: Shut down o/p voltage with auto-recovery or re-power on to recovery
OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down
ENVIRONMENT WORKING TEMP. -40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~+80℃ , 10-95% RH
TEMP. COEFFICIENT ± 0.03%℃ (0-50℃ )
VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X,Y,Z axes
SAFETY& EMC SAFETY STANDARDS Note.7 UL8750, CSAC22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP67 ,J61347-1, J61347- 2-13 approved; design refer to UL60950-1, TUV EN60950-1
WITHSTAND VOLTAGE I/P-O/P: 3.75KVAC I/P-FG: 2KVAC O/P-FG : 1.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG , 0/P-FG:100M Ohms/500VDC/25℃ /70% RH
EMC EMISSION Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ≥60% load); EN61000-3-3
EMC IMMUNITY Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547, EN55024 , light industry level (surge 4KV), criteria A
OTHERS MTBF 192.2K hrs min. MIL-HDBK-217F (25℃ )
DIMENSION 220*68*38.8mm(L*W*H)
PACKING 1.12Kg ; 12pcs/14.4Kg/0.8CUFT
NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple and noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf and 47uf parallel capacitor.
3. Tolerance: indudes set up tolerance, line regulation and load regulation.
4. Please refer to "Driving Methods of LED Module."
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. A-type only.
7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1 , and FCC parti8.
8. Length of set up time is measured at cold first start. Turning the power supply ON/OFF quickly may increase the set up time.
9. The power supply is considered a separate component that will operate in combination with the final equipment. Since EMC performance will be affected by its installation, the final equipment manufacturers must re-qualify EMC Directives on the installed product.
10. Refer to warranty statement.
11. To fulfill requirements of the latest ErP regulations for lighting fixtures, this LED power supply can only be used behind a switch that's not permanently connected to the main system.

Downloads

Inquiry Form